China Slurry Pump - How Bearing assemble to pump bearing housing?
Bearing assembly: install the outer bearing of the transmission end to the China slurry pump bearing housing, including R, RS, S, ST, T and TU type base series.
China Do Pump is a China Slurry Pump Solution provider, including China Slurry Pump - How Bearing assemble to pump bearing housing?, How to Maintain China slurry pump - Bearing lubrication, How to Maintain China slurry pump - Adjust slurry pump impeller, how to maitain China slurry pump shaft seal?, What are the steps when China slurry pump stops?, What are the Reasons cause China slurry pump operate failure? , What are the inspections before China Slurry Pump starts, what are the features of China slurry pump, what are the type of China slurry pump, how to select a China slurry pump, for any question related to China slurry pump, contact China Do Pump at info@dopumpgroup.com or call us at +8615031104888.
1. Apply thin oil to the inner hole of bearing housing (China slurry pump parts code 004) at the drive end (note the drive end)
2. Install the outer ring of bearing (China slurry pump parts code 009D) into the drive end of the bearing housing slurry pump code 004, and tap the bearing evenly with a copper hammer to make it lean against the shoulder of the bearing body. Install the outer rings of the two bearings 009D on the S bearing assembly (ie, S and ST slurry pump parts base).
If only one drive end bearing is used, the positioning sleeve can be installed against the shoulder of the bearing body, and then the outer ring of the bearing 009D can be installed.
3. Apply the recommended amount of grease, To the bearing, and apply most of it to the bearing, and the rest to the gap between the shoulder and the bearing.
4. Apply a thin layer of grease to the inner surface of the end cover (China slurry pump parts code 024).
5. Install the end cap and eng cover shim (China slurry pump parts code 025) in the bearing body, screw in the end cover set screw (China slurry pump parts code 027) and tighten.
Bearing assembly: Assemble the shaft (China slurry pump parts code 073) to the bearing housing (China slurry pump parts code 004)
1. Place the bearing housing with the assembled lower end cover on the two pieces of wood, clean the bearing holes and apply grease.
2. Screw on the nut 311 for the hanging shaft and carefully lift the hanging shaft into the bearing body with the help of a crane. Tap the bearing gently until it abuts the outer ring of the bearing.
3. Apply a thin layer of oil to the inner surface of the end cover 024.
4. Put the end cap with end eng cover shim 025 into the bearing body, screw in the end cover set screw 027 and tighten it firmly.
Bearing assembly: install piston ring (China slurry pump parts code 108) and hexagon socket set screw
R, RS, S, ST, T and TU type bracket series
1. Coat the piston ring 108 with butter, install two labyrinth rings in the grooves of the labyrinth (China slurry pump parts code 062), and the gaps of the labyrinth rings should be staggered 180 ° from each other.
2. Slide the labyrinth sleeve on the shaft. Please note that the labyrinth 062 is installed on the transmission end. Push the labyrinth sleeve into the end cover until the labyrinth ring is blocked.
3. Press the labyrinth ring with the presser 301 and push the labyrinth sleeve into the end cover.
4. On the labyrinth sleeve at the transmission end, screw in two hexagon socket set screws to fix the labyrinth sleeve to the shaft.
5. Install the hexagonal thread plug on the bearing body and the grease nipple on the end cover.
6. You must refuel into the labyrinth sets to ensure the final function.
Bearing assembly (China slurry pump parts 005) are ready for installation.
China Do Pump is a manufacturer of slurry pump, sand pump. dredge pump, electric submersible sand pump and hydraulic submersible dredge pump with relative dredging equipment.For more China slurry pump solutions related to China Slurry Pump - How Bearing assemble to pump bearing housing?, contact Sand Pump Manufacturer China Do Pump at info@dopumpgroup.com or call us at +8615031104888.
